What Does 4C Mean On A Samsung Washer?

How to resolve a 4E or 4C error code on a washing machine The 4E (4C) error code indicates that the washing machine has detected a problem with the water supply. The most common reason for this error is a blocked or kinked water supply hose. Try the below troubleshooting steps to resolve. 1 Check the water hose A problem with the water supply is usually the result of low water pressure or a low flow rate on the mains water supply to the machine. This means that the water feeding into the machine is not flowing with enough force. The water pressure must be between 0.5bar and 8bar.

Fully power off and unplug your washing machine at the mains. Move the machine forward to give access to the water hoses. Check that there are no kinks or bends in the water hose connected to the machine and make sure the hose is not damaged.

2 Check the water supply Check that the water tap connected to the washing machine is open to full.3 Clean the water hose mesh filter at least twice a year to prevent build up.

Turn off the water supply Disconnect the inlet hose from the water supply Disconnect the L-shaped arm from the washing machine Gently pull out the mesh filters Rinse the mesh filters under running water until they’re clean Reinsert the mesh filters Connect the hose again, first to the washing machine and then to the water supply Make sure the connections are watertight Turn on the water supply

4 Clean the dispenser drawer Occasionally, a 4C check code error message may be displayed if there is a blockage in the dispenser drawer. Follow the steps below or consult our step-by-step guide to,

Remove the drawer Check for any obstructions Clean if required Insert the drawer back into the washing machine

Why is my Samsung washer blinking 4C?

Resolve 4C or 4E error codes on your Samsung washing machine Your washing machine will display an error code or blinking light to alert you when there’s an issue with your appliance. The 4E and 4C error codes will appear if your washing machine cannot fill with enough water to run a cycle. This is usually caused by the washing machine’s hoses.

This guide will step you through the process. Note: Do not use Flood Safe hoses with your washing machine. As mentioned, the errors 4E and 4C indicate that your washing machine is not receiving enough water, and the issue is usually caused by a problem with one of the washer’s hoses. Depending on your model, the errors may also appear as nF or 1 4C.

Fortunately, we have some steps to help your washing machine fill up again.

Your washing machine’s mesh filter screens may be clogged. To clean them, turn off the water supply, disconnect the water supply hoses, and then clean the filter screens gently, like with a toothbrush or other similar small brush. While the water supply hoses are disconnected, check if they are kinked or clogged. Reconnect the water supply hoses, and make sure the faucets’ hot and cold hoses are connected to the corresponding water inlets on the washing machine. Then, turn on the water supply and make sure it is opened all the way for both the hot and cold water lines. Check that the drain hose is properly inserted and secured. A loose or incorrectly installed hose could be the source of the problem. The drain hose should not be inserted more than 6 inches into the drainpipe and should not form an airtight connection. You should also if it is dirty. If you have a top load washing machine that isn’t receiving enough water but is not showing a 4E or 4C error, you can add more water to it by using a different cycle. You can use the Deep wash or Deep fill cycles. Please contact to request service if the error still appears. Note: Do not remove the screw on the back of the washing machine that holds the drain hose against it. If the screw has been removed, screw it and the holder back in with any screw that fits. If the holder is missing, then,

Thank you for your feedback! Thank you for your feedback! Your comment has been submitted. © 2023 Samsung Electronics America, Inc. Samsung, Samsung Galaxy and Family Hub are trademarks of Samsung Electronics Co., Ltd. All other brands, products and services, and their respective trademarks, names and logos, are the property of their respective owners.

The above content is provided for entertainment and information purposes only. Consult user manual for more complete information. All information included herein is subject to change without notice. Samsung is not responsible for any direct or indirect damages, arising from or related to use or reliance of the content herein.

: Resolve 4C or 4E error codes on your Samsung washing machine

How do I reset my Samsung washing machine error code?

Reset your washing machine – There really isn’t a way to reset the washing machine. What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again.

Why won t my Samsung washer unlock?

Welcome to the ! Please enjoy our special offers for you Sorry, there is insufficient stock for your cart. Remove a Product Without this product, applied coupon or promotion code cannot be redeemed. Are you sure to remove this product? Check Preferences Help us to make recommendations for you by updating your product preferences.

1. Home

/

2. Samsung washer door is locked

Your washer door locks to prevent water from coming out (especially for front load models). Child Lock also will lock the door on some models, like front loaders. Normally waiting for the cycle to end is all you need to do to unlock the door, or turn your washer on if it’s off.

How do I reset the code 4C on my Samsung dishwasher?

Error 4C – With error 4C, the dishwasher has a problem with the water supply. Check the water supply and open it completely. Check if the supply hose has any bends or blockages, and remove them. Also clean the filter inside the dishwasher. Doesn’t the error go away? Check the water pressure.

What does 4C mean?

Step Two – Check the Water Hoses – The next step is to check the water hoses to make sure they are not defective. Faulty water hoses are the main cause of the 4C error code appearing. Sometimes they can get kinked, bent out of shape, or blocked up, which causes the water to not be able to get into the washing machine correctly. Here’s how to check the water hoses:

Turn the power off to your washing machine.Gently pull your washer out from the wall so you can access the back of it.Check if the hoses are kinked or bent out of shape, which will stop water from being able to properly flow through them.Check that the hoses are connected tightly. When they are not connected properly, this can adversely affect the function of the water valves that might be inside the hoses.The next step is to clean the hoses out, which you can do by first turning the water supply off and then disconnecting the hoses from both ends.Run water through the hose, and see if there are any blockages. If so, clean the hose out with a piece of wire until you unblock it. Also, check that there are no leaks in the hose. Once cleaned move on to step three (but don’t reattach them yet).

Why is the red lock light flashing on my Samsung washing machine?

This may be because the child lock is on but may also be because the cycle is not finished or the machine has detected an error. Note that after some cycles, the machine and laundry will be hot when the cycle ends, and the machine will only unlock after it has cooled down for safety reasons.

Why is my Samsung washing machine not draining or spinning?

If your washer doesn’t drain or spin: Make sure the drain hose is straightened. If you have a kink in the hose, it may restrict any water from draining. Make sure the debris filter is not clogged. If you are able to open and close the door, close it and press START/PAUSE.

How do I fix my washing machine error?

HE1 or HE2 is shown on the display of my washing machine. How can this be fixed? | Samsung Levant HE1 or HE2 indicates Heater Error. Please turn off the washer dryer and wait for about five minutes to cool it down and after that restart it and check. If the fault still persists, please contact Samsung Customer Care with respect to your country location,

UAE : 800-SAMSUNG (800-7267864) – From 08:00 am – 10:00 pm (All Week Days). OMAN : 800-SAMSUNG (800-7267864) – From 08:00 am – 10:00 pm (All Week Days). BAHRAIN : 8000-GSAM (8000-4726) – From 07:00 am – 09:00 pm (All Week Days). Kuwait : 183 (CALL) 2255 – From 07:00 am – 09:00 pm (All Week Days). Qatar : 800 (CALL) 2255 – From 07:00 am – 09:00 pm (All Week Days).

You may also book a repair thru, : HE1 or HE2 is shown on the display of my washing machine. How can this be fixed? | Samsung Levant

Why won’t my washer drain or unlock?

Check the Water Level Control – If your washer won’t drain or spin, the water level control may be faulty. Open the machine’s control panel and look for a plastic tube attached to the water level valve. If it’s clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.

How do I force my Samsung dishwasher to reset?

How to reset your Samsung dishwasher When something goes wrong with your dishwasher, such as an error code or if it’s not draining, you may think all that’s needed is a good reset. A lot of the times, weird electronic glitches (such as those that might occur after a power outage) might be cleared with such a reset, but if this doesn’t restart your dishwasher, then additional troubleshooting will be required.

However, depending on what error you get or issue you have, it’s not always a good idea to reset at the first sign of trouble. Read on for how to reset, when you should or shouldn’t, and what to do if a reset doesn’t help. Resetting your dishwasher is easy. Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the dishwasher (usually 1 to 5 minutes at most), and then power it up again.

That’s it. That’s all it takes to reset. Resetting your dishwasher will clear out all the error codes in memory. You might think “Great, now my dishwasher will start working again,” but it’s a little more complicated. First of all, most error codes signify an issue with your dishwasher that you need to address.

• If your at all, especially if it’s recently installed, then it’s likely to be an issue with the installation. In that case you should review the installation, preferably with a professional installer.
• If you have a, often with error codes like 5C, 5E, OC or OE, then it’s often something to do with the way the drain hose is installed, and again a reset won’t fix it if you don’t take care of the drain hose first.
• You can also see our guide for a list of what troubleshooting to do for each code, or our article for models without a digital display. If you have a different issue, try searching for it from to find a guide specific to the issue you’re having.

So when should you reset? After performing all the troubleshooting first. Some error codes will stay on the dishwasher even after you have done what it takes to fix them, so that’s when resetting the dishwasher is the next logical step. If a reset doesn’t clear the code, and you tried all of the troubleshooting steps first, you’ll have to request service.

1. Hold Smart Control until AP displays (about 3 seconds).
2. Hold Hi-Temp Wash until the dishwasher chimes (about 7 seconds).

Thank you for your feedback! Thank you for your feedback! Your comment has been submitted. © 2023 Samsung Electronics America, Inc. Samsung, Samsung Galaxy and Family Hub are trademarks of Samsung Electronics Co., Ltd. All other brands, products and services, and their respective trademarks, names and logos, are the property of their respective owners.

1. The above content is provided for entertainment and information purposes only.
2. Consult user manual for more complete information.
3. All information included herein is subject to change without notice.
4. Samsung is not responsible for any direct or indirect damages, arising from or related to use or reliance of the content herein.

: How to reset your Samsung dishwasher

What is error 4 E on Samsung dishwasher?

Error code 4C/4E – This code indicates a water supply error. This code will be displayed if there is no water in the dishwasher tub six minutes after the cycle starts. This code often indicates a problem with the water inlet valve. In order to troubleshoot this, you need to check that the water supply cut-off valve is open fully.

Can you stop and restart a washing machine?

How to stop your washing machine mid-cycle Have you ever found yourself frantically pushing every button or tugging at the washing machine door repeatedly after a last minute realisation that your mobile phone’s been left in your jeans pocket, or a delicate item’s accidentally made its way into a hot-water wash? If so, you’ll agree that knowing how to stop your washing machine-mid cycle is well worth getting to grips with.

1. Watch our video guide to find out how to safely stop your washing machine in an emergency, leaving you free to open the door and retrieve your items from the cycle.
2. There are a huge number of different washing machines available in today’s market and they all work slightly differently, so a ‘one size’ fits all solution to manually stopping a cycle doesn’t really exist.

We definitely recommend consulting your user manual first, before taking any of the steps below to try and open the door. You may be able to find the manual online if you’ve lost your copy (if you’re struggling, the website is likely to have it) or you could even look up the manufacturer’s number and give them a call.

If not, one of the three options outlined below is sure to work for most washing machine models. Go to step: Select a step Step 1 – Option 1 Step 2 – Option 2 Step 3 – Option 3 Press the “Start/Pause” button on your washing machine and wait a few minutes for the washer to safely drain away water in the drum before it unlocks the door.

Once this is done, you’ll be able to open the door and make any changes to the cycle. To resume the cycle, press the “Start/Pause” button again. Turn the dial cycle to “0” or “OFF” to end of the current washing cycle. Wait a few minutes while the appliance drains away the water from the drum before unlocking the door. Once you’ve made changes to the cycle, it won’t automatically continue, so you’ll need to re-enter your washing instruction if you need to continue with your washing.

If there’s a real emergency and nothing else is working, or the appliance is malfunctioning, you can pull the power plug out of the machine to stop the power. Please be careful if you do opt for this solution – the water may not have fully drained out yet. Put towels under the machine to soak up any water that may spill out when you open the door.

: How to stop your washing machine mid-cycle

Why won’t my washing machine finish its cycle?

What to do when your washer stops mid cycle When you load your washer and select the wash cycle, you might not give it a second thought. That is, until your mid cycle. There are a number of possible causes for your washing machine not working as it should.

1. If you find yourself in this situation, there are a few things you can check before calling in the professionals.
2. The first thing to check is your power supply.
3. If the power goes out in the middle of your wash cycle, it’s obvious that your washer will turn off too.
4. Similarly, if the plug you’re using for your washer is faulty, your washer will stop working.

So, before doing anything else, make sure that you check your power supply and test the plug. If none of these are to blame, it’s time to consider possible faults with your washer. Some of the most common faults that will make your washer stop mid cycle include thermostat failure, problems filling up with water for the rinse cycle, or even pump problems that prevent your washer from draining.

1. One thing that you can check yourself is the lid switch.
2. When you close the lid or door of your washer, there is a sensor that tells the washer it is properly closed.
3. If this switch malfunctions or breaks, the washer will “think” that the door is still open and it may not start, or it could stop before running the spin cycle.

If this is the case, the switch should be replaced by a professional. Not only will they be able to get the appropriate part, but they will also be able to perform reliable repairs. Another possible cause is the build up of residue from your laundry detergent.

• When the rubber hose in the back of your machine becomes clogged, it cannot activate the pressure switch.
• Fortunately, your repair technician will know just how to check for this problem, and it should only require cleaning and no part replacements.
• The pump could also be to blame if your washer is failing to drain.

Old washers used pumps that were run off the motor. Today, however, the newer models use self-contained pumps, and they tend to be less reliable. This kind of problem can be tricky to diagnose and, rather than stripping your washer and potentially making the problems worse, call your local appliance repair specialist for fast, reliable repairs.

If your washer stops while it’s still full of water, you will need to figure out how to get the water out without completely wrecking your laundry room. The first thing you need to do is grab plenty of old towels and buckets or anything you can use to catch the water. While you might not want to disconnect any hoses on your own, it’s best to have everything handy before the repair technicians arrive.

Different makes and models mean that every washer is different. All the more reason to hire an expert. For fast washer repairs anywhere in the GTA, at (647) 478-9692. : What to do when your washer stops mid cycle

What is error code 4c 2 on Samsung?

According to the owners manual, 4C2 is a trouble code referring to the cold water supply hose being improperly connected, possibly causing your delicate wash to fill with hot water. Your machine is programmed to wash delicates in cool or cold water. Probably check with whoever performs maintenance for you, and find out if the cold water is attached properly and if it is turned on.

Verified Purchase